If you’re looking to install a dropper post on your bike, Bike Yoke is a great option. Here’s a step-by-step guide on how to do it.
First, remove the seatpost from your bike.
Next, insert the Bike Yoke dropper post into the frame. Make sure that the post is properly seated in the frame before tightening the collar. Once the post is secure, reattach your saddle and seatpost clamp.
Now it’s time to adjust the height of the dropper post. The best way to do this is by sitting on your bike and raising or lowering the post until it’s at a comfortable height for you. Once you’ve found the perfect height, tighten down all of the bolts on the dropper post so that it doesn’t move while you’re riding.
And that’s it! You’re now ready to hit the trails with your new Bike Yoke dropper post.
- Using the 5mm hex key, loosen the set screw in the lever clamp 2
- Remove lever from handlebar 3
- Unscrew and remove bottom out assembly from post 4
- Install Bike Yoke dropper in its place following instructions that come with it 5
- Reattach lever to handlebar using the supplied M5x30 screws and torque to 1
Bike Yoke Triggy Alpha Install
Bike Yoke Triggy Alpha is an easy to install dropper post that provides 35mm of extra drop over a standard post. It’s great for riders who need a little extra room to maneuver on the trail. The installation is simple and only takes a few minutes.
Once installed, the Triggy Alpha provides a smooth, controlled ride with plenty of clearance for obstacles.
Credit: m.pinkbike.com
How Do You Reset the Yoke Dropper Post on a Bike?
Over time, the yoke on a dropper post can become loose, making it difficult to reset the post. Here’s how to do it:
first, remove the saddle and any other accessories from the bike.
Next, locate the yoke nut at the base of the post. Using a wrench or an Allen key (depending on your post), loosen this nut until it is completely removed.
With the yoke nut removed, you should be able to pull out the old yoke and replace it with a new one.
Once the new yoke is in place, tighten down the yoke nut until it is snug. Be careful not to overtighten, as this could damage the post.
That’s it!
You’ve now successfully reset your dropper post’s yoke.
How Do You Install an Internal Dropper Post Cable?
An internal dropper post is a great way to clean up your frame and get rid of those pesky external cables. Installing an internal dropper is a bit more involved than your typical cable install, but we’ll walk you through it step by step.
First, start by removing your old seatpost and bottom bracket.
You’ll need a few different size hex wrenches to do this. Once the seatpost and bottom bracket are out, use a utility knife to carefully cut away the remaining cable housing from the frame. Next, run your new dropper post cable through the frame.
Start at the bottom of the seat tube and thread it up through the headtube. If your frame has internal routing, there will be specific ports for the cable to go through – make sure you follow these so that the cable doesn’t get pinched when you reassemble everything.
Now it’s time to connect the cable to the dropper post itself.
Each brand of dropper post has slightly different instructions on how to do this, so consult your owner’s manual or look up a video specific to your model if needed.
What Does a Bike Yoke Do?
A yoke is a bike part that connects the frame to the fork. It helps to distribute weight evenly and keep the fork in place.
Bikeyoke REVIVE/DIVINE installation / Installation
Conclusion
If you’re looking to make your mountain biking experience a little more comfortable, installing a bike yoke dropper post is a great way to do it. A dropper post allows you to lower your saddle on the fly, making it easier to navigate rough terrain. Plus, it can also help you maintain better control and balance while riding.
Here’s a step-by-step guide on how to install a bike yoke dropper post on your mountain bike.
1. Start by removing the old seatpost from your bike frame. To do this, first loosen the seatpost clamp using an Allen key or similar tool.
Then, pull the seatpost out of the frame.
2. Next, insert the new dropper seatpost into the frame. Make sure that it’s inserted all the way and that the minimum insertion mark is not visible.
Once again, use an Allen key to tighten the seatpost clamp.
3. Now it’s time to attach the cable housing for the dropper lever onto the frame. There are typically two ways to do this – either internally or externally routed cables – so consult your user manual for specific instructions based on your setup.
Generally speaking, though, you’ll need to thread one end of the cable housing through a port in your frame before attaching it to the lever itself (usually with a zip tie).