If you’re like most mountain bikers, you love the feeling of hammering through singletrack. But sometimes, after a long day on the trails, your bike just doesn’t feel as responsive as it used to. That’s where Bike Yoke Revive comes in.
This simple-to-install device can make your bike feel brand new again by improving suspension performance and increasing pedaling efficiency. Here’s how to install it:
1. Start by removing the old air spring from your fork or shock.
If you’re not sure how to do this, consult your owner’s manual or ask a qualified bike mechanic for help.
2. Once the old air spring is out, insert the Bike Yoke Revive into the fork or shock body. Make sure that the o-ring is properly seated in the groove before moving on.
3. Now it’s time to add air to your fork or shock according to the manufacturer’s recommended settings. For best results, use a high-pressure air compressor when adding air to avoid damaging the internals of your suspension component.
4., Finally, go out and enjoy your newly refreshed suspension!
- First, you’ll need to remove your old dropper post and seatpost clamp from your bike
- Next, you’ll need to install the new Bike Yoke Revive dropper post
- Once the dropper post is installed, you’ll need to adjust the seatpost height so that it’s properly positioned for your riding style
- Finally, you’ll need to install the new seatpost clamp that comes with the Bike Yoke Revive dropper post kit
Bike Yoke Revive 213
If you’re a mountain biker, then you know how important it is to have a good suspension. And if you’re looking for a great suspension, then you should definitely check out the Bike Yoke Revive 213. Thissuspension is designed to give you the best possible ride, and it’s also very easy to install.
The Revive 213 comes with everything you need to get started, including instructions. It’s made from high-quality materials, and it’s been tested in some of the most difficult conditions. So if you’re looking for a great suspension that will improve your riding experience, then you should definitely consider the Bike Yoke Revive 213.
Credit: www.singletracks.com
How Do You Revive a Bike Yoke Revive?
Assuming you mean a stuck bicycle seat post:
If your bicycle seat post is stuck, there are a few things you can do to try and revive it. First, if the seat post is made of metal, try heating it up with a blow torch.
This will sometimes loosen the metal and allow you to turn the seat post. If this doesn’t work, or if you don’t have a blow torch, you can try using WD-40 or another lubricant. Spray the lubricant onto the seat post and wait a few minutes before trying to turn it again.
Finally, if neither of these methods works, you may need to use a hammer and punch to drive the seat post out from the bottom.
What Does a Bike Yoke Do?
A bike yoke is a device that attaches the frame of a bicycle to the fork. It consists of two plates that are connected by a pin or bolt, and it allows the frame to rotate around the fork. The yoke is an important part of the suspension system of a bicycle, and it plays a role in absorbing shock from bumps in the road.
Bikeyoke REVIVE/DIVINE installation / Installation
Conclusion
In order to install the Bike Yoke Revive, you will need the following tools: a torque wrench, a 6mm allen key or hex bit, and a 10mm open end wrench. You will also need access to a work stand. If you do not have a work stand, you can use an upside-down bike frame or ask a friend to hold the bike while you work.
To begin, remove the rear wheel from the bike. Next, use the 6mm allen key or hex bit to remove the two bolts that secure the air canister to the frame. Once these bolts are removed, you will be able to pull out the old air canister.
Now it is time to install the new air canister. First, insert one of the provided O-rings intothe groove onthe bottom ofthe new air canister. Make sure that this O-ring is properly seated in order totightly sealthe connection between саnіѕtеr аnd frаmе when reinstalled .
Next , apply some of th e included grease t o th e opposite side of th e O – ring . This will help ensure smooth operation ofthe air canister when installed . Finally , alignth e new air caniѕter withth e opening in th e frame and reinstall th e two bolts that secure it in place using your torque wrench .
Be sure not t o overtighten these bolts !